Status: app version v26.11.250.0

Layer build-up

A volume (volume A/B or classic volume) can carry a layer build-up — e.g. topsoil, red layer, frost-protection gravel — and shows the material quantity per layer. It is saved with the project.

Controls on the card
Show surfaceOn volume A/B each side (reference, comparison) has a “Show surface” box; on a classic volume it is also “Show surface”. The viewport then draws the surface over the polygon as a mesh. It is display only and changes no figure.
Bulking, compactionTwo factors between 0.5 and 3. Haul-off (loose) = cut × bulking, fill demand = fill × compaction. They only act on these two lines, not on cut, fill, net or the layer quantities. The “i” next to them explains them briefly.
Layer build-up…, + Layer“Layer build-up…” adds the first layer. “+ Layer” adds more, up to 12. The list runs from top to bottom: the top layer lies directly under the top surface. Every change is one undo step. On a locked volume the list is locked.
Top surfaceVolume A/B only. The top surface is the side the layers are counted down from, that is the finished surface. The default is “Comparison”. On a classic volume it is always the cloud surface inside the polygon; there is no choice.
One layerFrom the left: colour, name, thickness with unit, then ↑ ↓ to move and ✕ to delete. An empty name reads “Layer n”. Thickness is between 1 mm and 10 m and is entered in the display unit. Below it, “area · quantity” of the layer: the base area and area × thickness.
Show layersDraws a surface at every layer boundary, in the colour of the layer above it. The lowest surface is the formation level. Display only, independent of “Show surface”.
Volume to formation levelVolume A/B only. The formation level is the top surface minus the sum of all thicknesses. With the box ticked, cut and fill are not calculated against the top surface but against the formation level. The side then carries the suffix “− 0.50 m (formation level)”, in the card, viewport, quantity report and GeoJSON. Cross sections coupled to the volume also calculate down to the formation level; stored cross-section sources without coupling do not. A classic volume has no such box.
Total and notes“Total” gives the total thickness and the total quantity of all layers. The note lines say how it is calculated (offset vertically, quantity = area × thickness), whether cut and fill are calculated “to the top surface” or “to the formation level”, how much of the area the top surface covers, and whether the display is coarsened. The quantities always use the fine grid.
How it works together
Layers onlyWithout “Volume to formation level”, cut, fill and net of the volume stay unchanged. The layer build-up only supplies the table: quantity per layer = area × thickness. The area is where the top surface has a height.
With volume to formation levelCut and fill are calculated against the top surface minus the total thickness. The layer quantities stay area × thickness. The build-up and the earthwork below it add up to the quantity down from the top surface: if the formation level lies below the existing ground, more cut or less fill is counted.
Which top surfaceIf the layers should lie under the new ground, the top surface is the comparison (after). If they should lie under the existing ground, it is the reference (before). The other side stays as it is.
FactorsBulking and compaction only change “Haul-off (loose)” and “Fill demand”. They apply per volume, not per layer, and with “to formation level” they are applied to the cut and fill against the formation level.
Display“Show surface” and “Show layers” are independent of each other and change no figure. Together they show the top surface and all layer boundaries.
Classic volumeLayers under the cloud surface only, with a quantity per layer. There is no top-surface choice and no formation-level calculation. The formation level appears as the lowest layer surface and in the quantity table.
OutputQuantity report (PDF): a “Layer build-up” block per volume in the basis section, a total per layer name when several volumes have one. GeoJSON: “layer_stack” and, with “to formation level”, “to_planum” and “planum_offset_m”. Surfaces as DXF: the “Surfaces as DXF…” button on the card writes the top surface, the layer boundaries (layers “UK <name>”) and the formation level as separate layers.
Example
CalculationA flat area of 100 m². The reference (existing) is at 0.00 m, the comparison (finished) at 1.00 m, the top surface is the comparison. Layer 1 “Topsoil” 0.20 m, layer 2 “Frost protection” 0.30 m. Quantities: 100 m² × 0.20 m = 20 m³ and 100 m² × 0.30 m = 30 m³, total 50 m³ at 0.50 m total thickness. Without the formation level: fill 100 m³. With “Volume to formation level” the formation level is at 0.50 m: fill 50 m³. The build-up (50 m³) and the fill to the formation level (50 m³) add up to 100 m³ again. If the reference were at 0.70 m, it would be 30 m³ fill without and 20 m³ cut with the formation level.
LimitsThe layers do not wedge out and do not end at the ground. The offset is vertical: on a slope the layer is thinner than entered when measured at right angles to the surface; the quantity stays area × thickness. Varying thicknesses do not exist. The surface display has the resolution of the calculation grid, not of the cloud.

Work with your own point cloud.

Open point clouds, trace existing features and export geometry for CAD — directly in your browser, with point cloud data processed locally.

Try free for 14 daysRequest a demo