Status: app version v26.11.250.0
Volume A/B tool
The “Volume A/B” tool computes fill and cut between two surfaces inside a drawn polygon. The result is a shape: it stays in the shape list and is saved with the project.
| Drawing | Pick the “Volume A/B” tool and draw the polygon as with the Volume tool; Enter finishes. The polygon itself is the boundary of the computation — a marked boundary plays no role here. Vertices, layers, locking, duplicating and undo work as for any shape. An existing area, closed polyline (≥ 3 points) or standard volume can be turned into a volume A/B via “Convert” (and back). |
| Shape card | The card has two rows: “Reference (before)” — e.g. the original terrain — and “Comparison (after)” — the new terrain. Where the comparison lies below the reference, that is cut; above it, fill; net = fill − cut. Default: reference slot A, comparison slot B. |
| Sources | Per row: point cloud slot A or slot B, the active DEM, or a horizontal plane at a fixed height (in the selected unit, pre-filled with the lowest polygon point). The slot transform (translation/alignment) is taken into account. A DEM from a slot with a still-open transform is refused, as are two surfaces in different coordinate frames or an empty slot — the card then shows the reason instead of a number. |
| Points and cell value | For a point cloud: “Ground only (class 2)” or “All points” — without a ground class, “Ground only” falls back to all points with a notice — and per raster cell “Mean” or “Lowest point”. The default is “Lowest point per cell”: robust against stray points above the ground (vegetation, people, air points) that lift a mean. The “i” button explains both right in the card; if single cells deviate strongly, the card reports probable stray points. |
| Resolution | 1× / 2× / 4× refines the computation grid. 1× uses an automatic cell size from the point density (about nine points per cell), 2× and 4× halve or quarter it — never below 0.05 m and never beyond the computation budget. The notice line shows coverage, the share of filled holes (“interpolated”) and the cell size. |
| 3D columns | In the viewport, each counted raster cell gets a column between the two surfaces — you choose the cut and fill colours under Settings → Display → Cut/fill colours (default: cut yellow, fill red) and they apply everywhere. Columns at the polygon edge are trimmed to the polygon. With very many cells, blocks are merged. The label reads “Cut · Fill · Net”. |
| Always current | The result is always current: it is recomputed after drawing, at the end of every vertex drag, on every change in the card, when clouds or slots change and when a DEM is built; after a slot translation once the gizmo gesture ends. The settings are saved, not the numbers — they are recomputed after loading. |
| Replace inside terrain surfaces | With the source “Point cloud” or “DEM”, the volume is computed inside the chosen terrain surfaces with their height instead of the source. The cloud itself stays unchanged; the replacement applies only in this volume A/B. If a chosen terrain surface is deleted or cannot be computed, the volume is blocked and the card names the reason. |
| Example: sandbox | Sandbox volume: draw the rim as an area (Area tool), then use “Offset” with side “inner”, a distance and a negative Z offset (depth) and switch on “Vertical connectors (original ↔ offset)”. Pick that layer as “Constructed surface (TIN)” for the reference, set the comparison to the point cloud of the filled box and draw the A/B polygon along the rim (Shift-snap to the rim corners). If the copy is on a different layer than the rim, pick both layers. Bottom, connectors and rim form ONE surface, the bowl; “Show TIN” makes it visible. If you do not want the bottom as a shape of its own, untick “Create offset shape” in the Offset dialog — then only the connectors are created; the volume stays the same only for simple shapes with vertices at the corners (e.g. a rectangle), while with re-entrant corners (L shape, measured 3 to 6 % too little) or when the rim is densified afterwards (measured: up to almost the entire volume is then missing) the mesh needs the offset shape. Vertical walls work with distance 0: when rim and bottom share the same location, the reference uses the lower and the comparison the upper height — “Show TIN” then draws the wall between the two heights (display only, the number stays the same). It also works without the Offset tool: two hand-drawn outlines — rim and bottom — on the selected layer give the same bowl; with hand-drawn outlines the deviation is below about half a percent. Connecting lines between rim and bottom are only needed when the rim is densely set with points (densified or from a DXF file) AND the slope band is wide (wider than about a quarter of the pit): then the volume can come out a few percent too small (measured 2 to 4 %). In that case draw connecting lines between rim and bottom, e.g. via the offset series. For steps or berms in the slope: click a single connector — a “+” appears on its edge midpoint that inserts an intermediate point you can drag (this already works on the unchanged connector line). To keep editing the connectors as polylines (e.g. continue or split), select them all and choose “Convert to polylines” in the group bar; after the group conversion click a single connector again, then the “+” appears. Overhanging walls cannot be represented: there is only one height per location. |
| Constructed surface | Choose the source “Constructed surface (TIN)” and pick layers (list with shape counts): all visible points, lines and areas of these layers form a triangle mesh, every shape edge acting as a breakline. Typical use is an offset series with a Z offset as formation-level or embankment lines. Crossings and T-joints are split, points closer than 1 mm are merged, triangles without overlap with the A/B polygon are dropped; hull peeling acts on the whole mesh, independent of the polygon. “Max. edge length (× median)” (1–20, default 3) peels overly long outer edges — never across a breakline; outside the mesh there is no height (no extrapolation). “Show TIN” draws the mesh in the viewport as a semi-transparent shaded surface with its wireframe — so you can see that bottom, connectors and rim form ONE surface (a bowl). It is recomputed after a formation-level line has been dragged and when a chosen layer is hidden or shown; the mesh works without an open point cloud (e.g. TIN against a plane). |
| Offset: narrow spots | If the area is narrower than twice the inward distance in some place (an arm, a notch, a rounded corner), that place drops out of the offset instead of forming a loop. If the area splits into several parts, the offset creates several areas ("Part 1/2", "Part 2/2") — one Ctrl+Z undoes them all; the installed base (slope) is then not created. This also applies to the outward offset: a narrow cut-in (such as the gap of a U shape) is closed, and the status line says so. The vertical connectors follow the outline up to the cleaned-up corners and do not cross each other; if a connector has to be dropped for that (for instance because its target lies behind a re-entrant corner), the status line says so. An open line is not cleaned up: if the offset line crosses itself in a tight curve, it stays unchanged and the status line warns. If the offset cannot be cleaned up at a narrow spot, the status line says so and shows the unchecked offset. A remainder smaller than 1 % of the distance does not count as an offset (it is dropped, or the offset is reported as too large). For very extensive outlines the self-overlap check may not run to completion — the status line says that too; the result is then the same as before. |
| Bulking and compaction | Below the figure there are two fields: bulking (loose quantity per solid quantity of cut) and compaction (quantity to deliver per solid quantity of fill built in). Values from 0.5 to 3 are allowed, rounded to two decimals; an empty field counts as 1. The app knows no soil properties; the factors are your input. With a factor other than 1 the rows "Haul-off, loose" (cut × bulking) and "Fill demand" (fill × compaction) appear. The A/B figures cut, fill and net stay solid-measured and do not change; there is no "net loose". The factors do not trigger a recalculation, apply per volume, are saved with the project and appear as extra properties in the GeoJSON export. On locked volumes the fields are locked. A change is one undo step. |
| Show surface | Each side (reference, comparison) has a “Show surface” checkbox: the viewport then shows the surface over the whole polygon as a shaded, semi-transparent mesh with wireframe, in the colour of that side. The mesh is built from the calculation grid with exactly the heights the volume calculates with, so figure and picture belong together. It shows the common area in which both sides have a height; cells without a height stay holes, and at the polygon edge the mesh ends at the polygon. It has the resolution of the calculation grid, not of the cloud. With very many cells, cells are merged block-wise and the card names the coarsening. A normal volume also has “Show surface” (the cloud surface inside the polygon, with a stepped edge like the figure). The checkbox is saved with the project, is not a calculation input and does not change the figure. |
Work with your own point cloud.
Open point clouds, trace existing features and export geometry for CAD — directly in your browser, with point cloud data processed locally.
Try free for 14 daysRequest a demo